POWER APPLICATIONS FOR FUEL-CELL USING SWITCHING REGULATORS

DEGA RAJAJI VANKA

Abstract


 

Generally the switch mode power supply input voltage source is constant or shows insignificant little varieties.in any case, when fuel call used input source the last assumption is not valid. A fuel cell stack is give a details of low and not controlled DC output voltage, moreover, when the demanded current increases the output voltage becomes low in a nonlinear form; from now on, suitable controller is required to taken the previously mentioned issues. In this article, a normal current-mode controller is planned to using a joined model for an energy unit stack and a boost converter; besides, the resolving control method increasing the system stability and output voltage regulation.. The proposed energy system utilizes an energy component power (polymer electrolyte film fuel cell) and a boost converter passing on power of 900 W. the proposed controller execution for output voltage regulation by means of closed loop gain estimations and step load changes. What's more, a correlation amongst open-and closed- loop estimations is made, where the controller robustness is tried for vast load varieties and fuel cell stack output voltage changes are shows on simulation results.

Keywords


Fuel Cell, Current mode Controller, Boost Converter and PI Controller

References


Carrasco, J.M., Garcia, L., Bialasiewiez, J.T., et al.: ‘Power-electronic system for the grid integration of renewable energy sources’, IEEE Trans. Ind. Electron., 2006, 53, (4), pp. 1002–1016

Benson, Ch.L., Magee, Ch.L.: ‘On improvement rates for renewable energy technologies: solar PV, wind, capacitors, and batteries’, J. Renew. Energy, 2014, 68, pp. 745–751

Shen, J.-M., Joul, H.-L., Wu, J.-C.: ‘Transformerless three-port grid connected power converter for distribution power generation system with dual renewable energy sources’, IET Power Electron., 2012, 5, (1), pp. 501–509

Jakhar, H., Soni, M.S., Gakkhar, N.: ‘Historical and recent development of concentrating photovoltaic cooling technologies’, Renew. Sustain. Energy Rev., 2016, 60, pp. 41–59

Bahceci, S., Fedakar, S., Yalcinoz, T.: ‘Examination of the grid-connected polymer electrolyte membrane fuel cell's electrical behaviour and control’, IET Renew. Power Gener., 2016, 10, (3), pp. 388–398

Rahmal, S.A., Varmal, R.K., Vanderheide, T.: ‘Generalised model of a photovoltaic panel’, IET Renew. Power Gener., 2014, 8, (3), pp. 217–229

Li, Q., Chen, W., Liu, Z., et al.: ‘Active control strategy based on vector proportion integration controller for proton exchange membrane fuel cell grid-connected system’, IET Renew. Power Gener., 2015, 9, (8), pp. 991–999

Thounthong, P., Davat, B., Rael, S., et al.: ‘Fuel cell high-power applications’, IEEE Ind. Electron. Mag., 2009, 3, pp. 32–46

Kabalo, M., Pairel, D., Blunier, B., et al.: ‘Experimental evaluation of four phase floating interleaved boost converter design and control for fuel cell applications’, IET Power Electron., 2013, 6, (2), pp. 215–226

Leel, J.-G., Choe, S.-Y., Ahn, J.-W., et al.: ‘Modelling and simulation of a polymer electrolyte membrane fuel cell system with a PWM dc/dc converter for stationary applications’, IET Power Electron., 2008, 1, (3), pp. 305–317




DOI: http://doi.org/10.11591/ijeecs.v15.i1.pp%25p
Total views : 63 times

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

shopify stats IJEECS visitor statistics